Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: FOR SALE: ENDYN Stepper Pulley

  1. #1
    Inactive Member JRSCGSR2817's Avatar
    Join Date
    July 11th, 2000
    Posts
    64
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    I'm selling the ENDYN Stepper Pulley from a '94 Integra GSR for $100 o.b.o. E-mail me at [email protected] if anybody's interested. Thanks.

  2. #2
    Senior Hostboard Member rjaffey's Avatar
    Join Date
    February 16th, 1999
    Posts
    764
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Question

    Why are you selling it?

  3. #3
    Inactive Member JRSCGSR2817's Avatar
    Join Date
    July 11th, 2000
    Posts
    64
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    The stepper pulley produced more boost than I expected, and since it's my daily driver, I want to either boost at a safer level with the JR crank pulley or part out my car and save up for the RSX-R next spring.

    [This message has been edited by JRSCGSR2817 (edited July 06, 2001).]

  4. #4
    Senior Hostboard Member rjaffey's Avatar
    Join Date
    February 16th, 1999
    Posts
    764
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Question

    How much boost did you wind up with? I wound up with just about 10psi. What were you expecting?

  5. #5
    Inactive Member JRSCGSR2817's Avatar
    Join Date
    July 11th, 2000
    Posts
    64
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    My boost gauge reads, at times 11psi, but most of the time it stays pegged at 10psi. I was only expecting 8psi.

  6. #6
    Inactive Member JRSCGSR2817's Avatar
    Join Date
    July 11th, 2000
    Posts
    64
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    Is there a major difference between power levels with the JR crank pulley and the ENDYN stepper pulley?

  7. #7
    Inactive Member The LS Avenger's Avatar
    Join Date
    March 30th, 2000
    Posts
    417
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    2 comments:

    Your boost gauge probably read so high on count of a restrictive exhaust setup. Many others have done this mode and gotten the expected 8-9 psi.

    Also, read up some more on the crank pulley approach here on hostboard. Unless JR is doing something special, the CRV C.P will spin everything faster, including your alternator and PS pump -- not good things !


  8. #8
    Inactive Member blownintegra's Avatar
    Join Date
    June 25th, 2000
    Posts
    297
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    Will it fit an LS? What kind of boost can I expect??????

    I might be very, very interested.

    Could someone knowledgeable chime in on this one??????

  9. #9
    HB Forum Owner 96IntegraRS's Avatar
    Join Date
    July 2nd, 2000
    Posts
    657
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    Hey Blownintegra: I'm not knowledgable, but:

    This is the same pulley I have.

    Chuck

    ------------------
    96 Integra B18B w JRSC@9psi, JR BTC, JR MAP Converter, Venom 270's, Walbro 342, DC 4-2-1, DC Catback, ST Rear Swaybar, etc.

  10. #10
    Inactive Member fastfour's Avatar
    Join Date
    October 27th, 1999
    Posts
    709
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    <BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by blownintegra:
    Will it fit an LS? What kind of boost can I expect??????

    I might be very, very interested.

    Could someone knowledgeable chime in on this one??????
    <HR></BLOCKQUOTE>


    The pulley will fit. It's funny though, b/c I only see around 7-8psi with mine. Wonder if that is why my gains with the pulley are so minimal???

    Zach


    ------------------
    94 Civic Coupe/LS Hybrid
    JRSC@9psi
    Turbo Convert
    Import Specialty Automotive (253) 473-2606

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •